Exactly How to Install a Bath Tub in Your Bathroom
Schedule ServiceRight here down the page you can find lots of sensible answers when it comes to How to Install a Bathtub Yourself.
Mounting a bathtub isn't exactly rocket science, however it does call for strong plumbing, carpentry, and sometimes, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably hard project. If the old tub is readily available, the job can relocate immediately; if you need to open up a wall surface to get rid of the old bathtub and also position the new bathtub, the task is much harder. In either case, the project is within a home handyman's skills, although you will need a helper to move out the old tub and set in the new one. Ensure you have qualified yourself for the job and are comfortable attempting it. Rather than hiring a contractor to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Possibilities are you may need a professional plumber to make tube connections.
This article will aid you mount a brand-new tub in your shower room if you have already acquired a brand-new bathtub as well as don't need to transform the setup of your previous water pipelines.
Your tools and product checklist should comprise the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain any kind of water staying in the system. The process of removing the existing faucets can be rather problematic as a result of the limited access that is often the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will originate from the pipelines. Once the supply pipelines have been removed, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old securing compound.
Prior to moving on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin making certain that the washers remain in area between the faucet and also the sink. Protect the faucet in position with the producer given backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous kind ought to be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Making use of the two wooden boards under its feet, put the bath tub in the required placement. The wooden boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
The next goal is to make sure that the tub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the bathtub up until the level reviews degree.
To mount faucets, fit the bottom of the furthest flexible tap port to the proper supply pipe by making a compression join; then do the exact same for the various other faucet.
Turn on the water and also examine all joints and also brand-new pipework for leaks and tighten them if necessary. Fill the bathtub and also check the overflow outlet and the normal outlet for leaks.
Finally, repair the bath paneling as described in the producer's instruction manual. Tiling and sealing around the bathtub should wait until the bathtub has actually been made use of at the very least when as this will certainly resolve it into its final position.
Preparing for the Setup
First of all, the supporting frame supplied with the bathroom needs to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make certain that if the tap features a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets device to avoid strain on the bathtub.
Fit the adaptable faucet ports to the bottom of the two faucets utilizing 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final position.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to crack a stiff seal, causing the water to pass through the wall in between the bath as well as the tiling, leading to issues with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and also cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched paper or soft rope. Remember to constantly fill the tub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealer can crack relatively very early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or waterproof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate more info about Tools You Need to Install a New Bathtub ? Leave feedback directly below. We'd be glad to listen to your responses about this article. We hope that you come back again in the future. Feel free to take the opportunity to distribute this article if you liked it. We value reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Request An Estimate